UnofficialBMW.com
Unofficial BMW

Unofficial BMW

Google Search





What's New

Search (Google!!)

FAQ

BulletinBoard

Classifieds

Garage

Images

Books

Tools

Parts

Used Cars

Links

FTP

Advertise

Search Amazon.com
In Association with Amazon.com
 

Home E12 E24 E28 E30 E34 E36 Z3 E39 E46 X5/E53 ALL
Ron Stygar Carl Buckland Dale Beuning Forums Help

Unofficial BMW Nav Map



From digest.v5.n288 Thu Sep 26 00:04:57 1996
From: "Anthony R. Dainora" <adainora_at_mindspring.com>
Date: Wed, 25 Sep 1996 21:50:21 -0500
Subject: Definitive word on Overrev

I have read the overrev thread with great interest these past few months since I am a proud owner of a 95 M3. I found the following article posted on the Houston BMW CCA web page. It was featured in their January 1996 newsletter "The Torque of the Town". IMHO it is an excellent discussion on overrev. The author James Williams with Advantage BMW in the Houston area relates his knowledge on this subject and his specific experience with E36 M3s. Since the article was not copyrighted, I'm posting it for those individuals who are interested in this subject.

Beyond Overrev by James Williams

Each and every rotating mechanical device on the face of the earth has a maximum rpm at which it can operate safely. From lawnmowers to Lear jets, engines
have a safe limit, with a margin to boot, commonly known as redline - it's clearly marked, right there on your tach, for all to see. Older cars with distributor-and-points type ignition would make spark at any engine speed, no matter if that engine speed was way over that engine's efficient redline. Our more modern engine management systems have the capabilities to omit spark and fuel at predetermined rpm. This is commonly known as a rev limiter. Rev limiters keep you from blowing the engine, right?

Let's clear up a misconseption: Rev limiters keep you from blowing the engine up with the throttle. The throttle could be held wide open with the gearbox in
neutral and, in theory, the engine would not suffer. Don't try this at home.

So, what exactly is over-revving and how does it occur? Let's start with some definition of terminology.

Overrev: to greatly exceed the given mechanical limits of rotating equipment.

Reduction Gearbox: the standard transmission is a reduction gearbox, converting engine speed down to a lower speed. Automatics do the same thing but are
not in discussion here. Transmission output drives the driveshaft, sending power to the differential, which is also a reduction gearbox. Thus, the engine has great leverage over the rear wheels.

Downshift: to shift the gearbox from fifth gear, to fourth, to third, etc. Motorcycles have a sequential gearbox, meaning the shifts only precede from one gear to the next. Automobiles have shifters that can select any gear, any time. Can you see a window for mistakes here? Can you say "miss a shift"?

Three times this year alone, I have had M3s fall into my hands . One came in running on five cylinders, the other two had been overreved so bad, engine replacement was required.

All three had bent exhaust valves, with the fatal two having bent intake valves as well. The piston crowns had round imprints and cresent shaped hammer marks
from the valve heads. In both cases, the final blow was identical: each engine had valves bent over so far, a spark plug was broken and, a piece of the porcelin center cone had lodged itself beside the piston and scarred the cylinder wall too deep to rebore. From one moment to the next, from a healthy engine to expensive junk.

How can this happen so often? What caused this to begin with? There is only one way possible and that is to miss a downshift and accidently stick the gearbox
into too low of a gear at too high high a roadspeed. In most cases, I believe this to mean missing a fifth-to-fourth downshift and making a fifth-to-second
downshift. Ouch!!

When this happens, the events that follow are swift and sure. For the sake of demonstration, let's say we are motoring along at a nice, safe 100mph. All is well and we are in top gear, with a corner in sight. We slow down and attempt to downshift to fourth gear. The shift is fumbled, second gear is selected by mistake, the clutch is re-engaged. Suddenly, the leverage the engine had over the rear wheels is history. Those big, wide rear tires have quite a bite on the road and do not slide. The transmission becomes an induction gearbox as the car and rear wheels are now driving the engine. The hapless engine is now being spun far faster than it's mechanical limit. What does "mechanical limit" mean in real life terms?

Let's step inside the engine and see what happens. An internal combustion engine of such high specific output is a well choreographed procession of parts narrowly missing each other and vulnerable pieces. Let's keep our eye on one cylinder to simplify things.. When the valve is closed, there is a small amount of clearance between the cam lobe and the lifter. As the camshaft turns at half engine speed, the cam lobe touches the lifter, raising the valve off its seat to full lift. The cam continues to turn and the valve springs keep the lifter in contact with the backside of the cam lobe. The valve is well. In our situation, however, the engine is suddenly spun so fast, the cam actually throws the valve open and the valve springs cannot overcome the inertia to keep the lifter in contact with the backside of the camlobe. Known as "valve float", the valve is open longer than the cam's intended duration. This also means that the exhaust valve is still extended into the cumbustion chamber as the piston reaches Top Dead Center (TDC). The piston slams into the valve head, bending it over like a nail. At these high rpms, the piston and valves crash into each other hundreds of times per second. By now, the driver has realized his mistake, kicked in the clutch and, as they say, it's all over but the shouting. The loudest sound to be heard now us the sound of his wallet screaming.

Can this horrible outcome be avoided? Yes, with careful and deliberate placement of the shifter. Does this happen only to M3s? No. Any car with a standard
gearbox is a potential victim. Know the top speed of each gear and learn it well. Must shifts be in sequence? No. Professional race drivers have different driving styles including downshifting. Two prime examples come to mind: Check out old Indy in-car camera shots of Nigel Mansell. Nigel downshifts so fast in sequence, the engine speed is never out of the powerband or far from the redline. Michel Andretti, on the other hand, slows for each corner in whatever gear he is in, then shifts to the proper gear at the apex of the corner and accelerates out at full-tilt-boogie. Either method is correct when applied correctly. Novice drivers new to sport driving, or and old pro, anyone can miss a shift in the heat of the moment. Presence of mind is the key here. Learn your limits and the limits of the car and mark it in your mind as clearly as that redline on your tach.

Hope my $.02 helps other drivers to avoid the consequences of overrev. I have also almost missed shifts on two occasions. Mind you I've seen my life flash before my eyes. No damage to the engine. Shifting gears get all of my attention all of the time.

Tony Dainora
1995 M3

Unofficial Homepages: [Home] [E12] [E24] [E28] [E30] [E34] [E36] [Z3] [E39] [E46] [X5/E53] [ALL] [ Help ]