![Unofficialbmw.com Forum Index](templates/subSilver/images/logo_phpBB.gif) |
Unofficialbmw.com The UnofficialBMW BB, answers for your BMW questions.
|
Support Unofficialbmw.com :: Download Free Healthy Habits iPhone app!
View previous topic :: View next topic |
Author |
Message |
dale
![](images/avatars/1747582731486d7c46d89ff.jpg)
Joined: 22 Aug 1999 Posts: 3087 Location: Seattle, WA USA
|
Posted: Thu Aug 31, 2006 11:47 am Post subject: Basement project 8/30/06 |
|
|
Basement sub-projects:
1) finish sheetrock
I knew this was a big project, so I hired a guy, Joe, to do the work. He did the 'rock in my garage as well a few years ago and does a very nice job.
Initially I was holding him up since I didn't have the shower installed and the bathroom insulated, and the hallway shear wall installed(7/16" osb), now that those are done, he has finished getting the 'rock up, and will start taping the seams today, Thursday.
He should be done by the 9th, and I have a guy starting on the 11th to do the trim work.
Just gotta get some primer on there in between.
2) re-route main floor bathtub drain around basement bathroom door!
The drain from upstairs was running right through the path of the basement bathroom sliding door:
old:
new:
now the door opens all the way, that's a good thing:
3) as I was working on the basement remodel, I noticed that the sill plate of the walls was just sitting on top of the foundation. I remembered Cher telling me about the earthquake she worked a long time ago where the houses that received a lot of damage did so because they fell off their foundations!
Check out this article on the 'shake house' created by a Univ http://www.usatoday.com/tech/science/columnist/vergano/2006-07-02-earthquake-simulator_x.htm
Univ Buffalo videos:
http://nees.buffalo.edu/projects/NEESWood/video.asp
I started researching seismic retrofitting, hired a structural engineer to come out and give me his opinion, and installed a bunch of anchors into the concrete: The small one in the middle is a 1/2" redhead anchor, with a nylock locking nut on top, and a 2" square bearing plate to distribute the load.
The BP (bearing plate, aka washer)
http://www.strongtie.com/products/connectors/BP-LBP.html
The structural engineer spec'd 1/2" anchor every 48", I went overkill with my new Bosch SDS driver and installed them every 12" !!!
http://www.amazon.com/gp/product/B00006AG7E/
Some specs on the Redhead Wedge Anchor
http://www.ramset-redhead.com/RH/trubolt_perf_1.asp
Redhead TruBolt
http://www.ramset-redhead.com/RH/trubolt.asp
The special angle pieces go at each end of a portion of the cripple wall, they are called 'pre-deflected hold-downs', they help keep that piece of wall tied together and vertical:
The bolts holding these down are 8" long 5/8" redhead expansion anchors
PHD2-SDS3
http://www.strongtie.com/products/highwind/shearwallholdowns.html#table
http://www.strongtie.com/products/connectors/PHD-HDQ8.html
Each one is good for about 3600 pounds of uplift
Here is the Autocad DXF file of this part:
http://www.strongtie.com/ftp/dxf/highwind/D83.dxf
Then you add "shear wall" so the cripple wall (aka knee wall, aka stub wall) won't "diamond" or "rack" or, in layman's terms, fall over:
Next you add connecting plates, to keep the main floor studs tied to the cripple wall, a Simpson Strong Tie LTP4 is what my local Home Depot had:
This page has the specs and ratings of this part:
http://www.strongtie.com/products/connectors/ltp4-ltp5-a34-a35.html
4) heating to bathroom and bedroom#1
When I had my framing inspection done, the inspector said, "if these are bedrooms and a bath, where is the heat?"
I had heat in the hallway and bedroom #2, but needed to add to the others.
Found that there is a 6" duct going to the upstairs bathroom just above the basement bath. I removed the 90 degree elbow and installed a 6" T fitting, then added a downward facing outlet into the bathroom. It happens to point in the lap of a person sitting on the toilet, oh well, should keep them toasty!
This one in bedroom#1 I just added the duct and outlet. The other end of the duct is laying in the crawl space at the moment, I'll get it hooked up soon
![](http://www.unofficialbmw.com/house/yellow-west-seattle/basement/aug-30-2006/medium/DSCN0337.JPG) _________________ http://www.unofficialbmw.com
UnofficialBMW.com Webmaster
dale@unofficialbmw.com
sold in 2016
87 325 5spd eta |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
See all UnofficialBMW Ads
|
dale
![](images/avatars/1747582731486d7c46d89ff.jpg)
Joined: 22 Aug 1999 Posts: 3087 Location: Seattle, WA USA
|
Posted: Thu Aug 31, 2006 6:03 pm Post subject: |
|
|
Redhead anchor performance specs:
Trubolt
Wedge Anchors
Ultimate Tension and Shear Values (Lbs/kN) in Concrete*
ANCHOR
DIA
In. (mm) INSTALLATION
TORQUE
Ft. Lbs (Nm) EMBEDMENT
DEPTH
In. (mm) ANCHOR
TYPE f'c = 2000 PSI (13.8 MPa) f'c = 4000 PSI (27.6 MPa) f'c = 6000 PSI (41.4 MPa)
TENSION
Lbs. (kN) SHEAR
Lbs. (kN) TENSION
Lbs. (kN) SHEAR
Lbs. (kN) TENSION
Lbs. (kN) SHEAR
Lbs. (kN)
1/2 (12.7) 55 (74.6) 2-1/4 (57.2)
4-1/8 (104.
6 (152.4) 4,660 (20.7)
4,660 (20.7)
5,340 (23. 4,760 (21.2)
7,240 (32.2)
7,240 (32.2) 5,100 (22.7)
9,640 (42.9)
9,640 (42.9) 4,760 (21.2)
7,240 (32.2)
7,240 (32.2) 7,040 (31.3)
10,820 (48.1)
10,820 (48.1) 7,040 (31.3)
8,160 (36.3)
8,160 (36.3)
5/8
(15.9) 90 (122.0) 2-3/4 (69.9)
5-1/8 (130.2)
7-1/2 (190.5) 6.580 (29.3)
6.580 (29.3)
7,060 (31.4) 7,120 (31.7)
9,600 (42.7)
9,600 (42.7) 7,180 (31.9)
14,920 (66.4)
15,020 (66. 7,120 (31.7)
11,900 (52.9)
11,900 (52.9) 9,720 (43.2)
16,380 (72.9)
16,380 (72.9) 9,616 (42.
12,520 (55.7)
12,520 (55.7) _________________ http://www.unofficialbmw.com
UnofficialBMW.com Webmaster
dale@unofficialbmw.com
sold in 2016
87 325 5spd eta |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
dale
![](images/avatars/1747582731486d7c46d89ff.jpg)
Joined: 22 Aug 1999 Posts: 3087 Location: Seattle, WA USA
|
Posted: Sat Sep 09, 2006 12:26 am Post subject: |
|
|
Drywall was finished today, Friday 9/8. Start painting with Primer on Saturday.
Trim work starts on Monday 9/11, should be done Friday 9/15.
Final paint that weekend and then just the floors to finish.
Dale _________________ http://www.unofficialbmw.com
UnofficialBMW.com Webmaster
dale@unofficialbmw.com
sold in 2016
87 325 5spd eta |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|