View previous topic :: View next topic |
Author |
Message |
patrickf
Joined: 15 Mar 2009 Posts: 4 Location: Rochester, New York
|
Posted: Sun Mar 15, 2009 3:26 am Post subject: stubborn lower control arm 2000 328i |
|
|
I am replacing the lower control arms on my 2000 328i. All went well on the driver's side but I can't remove the lower ball joint on the right side (outer, connected to wheel). I have a ball joint separator locked on to the point where it is beginning to bend the bolt. Looking for hints, tricks, suggestions. I have squirted PB Blaster to no effect.
I was thinking of removing the ball joint separator and using a pickle fork instead. But I'm afraid of harming the suspension setting by whacking on it. |
|
Back to top |
|
|
|
edjack
Joined: 04 Feb 2002 Posts: 3887 Location: San Jose, CA
|
Posted: Sun Mar 15, 2009 8:05 am Post subject: |
|
|
A pickle fork is a barbaric way to separate joints, but, if you have to, you have to. If you have an air chisel, use the fork made for it.
I would crank down on the separator, and leave it set overnight. May pop then. _________________
Ed BMW CCA member since 1987 (Nr. 62319).
'97 540i 6 speed Aspensilber over Aubergine interior. |
|
Back to top |
|
|
patrickf
Joined: 15 Mar 2009 Posts: 4 Location: Rochester, New York
|
Posted: Sun Mar 15, 2009 9:09 am Post subject: |
|
|
Exactly! The pickle fork was a last resort. I did leave the ball joint separator cranked down overnight hoping I would see it hanging in the morning but now such luck.
So I will be trying an air chisel shortly. Man, this one is on there. I'm hosed if I can't get it off. Who said this job was easy?! Good thing the garage is heated. |
|
Back to top |
|
|
patrickf
Joined: 15 Mar 2009 Posts: 4 Location: Rochester, New York
|
Posted: Sun Mar 15, 2009 4:52 pm Post subject: |
|
|
OK, its done. After I made the bolt on the lower control arm bushing look like a bent finger I tried the pickle fork and winced. I was ready with the air chisel but opted for heat. I cut off the bent portion of the bolt. A friend of mine brought over his acetylene torch and we heated up the housing around the bolt. I struck the pickle fork in there and with a tap, it released. Finally.
A test drive confirmed the obvious, the bushings were shot. Tight tight tight. Awesome. The PowerFlex urethane bushings are so much better than stock BMW rubber bushings.
What I don't understand is the BMW fix for this. They went to a stronger, 66mm control arm but did nothing to upgrade the outer bushing (I purchased Mayle's). I would think they would re-design that portion too. So, I went aftermarket.
I purchased both from bimmerworld. Very satisfied.
Thanks for the advice. |
|
Back to top |
|
|
SSearch
Joined: 15 Apr 2003 Posts: 591 Location: Vermont, USA
|
Posted: Fri May 08, 2009 12:48 pm Post subject: |
|
|
I've fought with ball joints, pitman arms, etc - Living in Vermont, trust me, some of them have put up a good fight. I usually crank the seperator down, and then give the top of the bolt a solid whack. The shock tends to be just what's needed for the stubborn ones. _________________ 02 330XI |
|
Back to top |
|
|
ddupy
Joined: 17 May 2009 Posts: 10 Location: SE Iowa
|
Posted: Tue May 19, 2009 11:55 pm Post subject: |
|
|
I had a 93 318is that I replaced the control arms on. They just practically fell off!! I guess I was just lucky............ _________________ 2002 325i M-Technic
|
|
Back to top |
|
|
|