![Unofficialbmw.com Forum Index](templates/subSilver/images/logo_phpBB.gif) |
Unofficialbmw.com The UnofficialBMW BB, answers for your BMW questions.
|
Support Unofficialbmw.com :: Download Free Healthy Habits iPhone app!
View previous topic :: View next topic |
Author |
Message |
McK
Joined: 27 Mar 2003 Posts: 1126 Location: Chicago
|
Posted: Thu Jun 09, 2005 9:34 pm Post subject: COOKED Brakes (photo) |
|
|
I threw this in the racing forum, only because this was at a track event, on a 2003 M3 with rcomps and race pads (Cobalt, I think). This guy is notoriously hard on his brakes... the session before I snapped this photo he had flames shooting out of the wheels under full braking.
These were stock M3 cross drilled rotors before he went out on the course. Every single hole was FUSED full of what we assume was a combination of pad material and rotor shavings (you can see how darn worn those rotors are).
Just had to share that pic, it blew our mind. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
McK
Joined: 27 Mar 2003 Posts: 1126 Location: Chicago
|
Posted: Fri Jun 10, 2005 12:19 pm Post subject: COOKED Brakes (photo) |
|
|
The driver sent me a follow-up pic. This was his brake pad when he took it off the car:
Yes it's bent. Not quite down to the backing plate but very close. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Chuck Baader
Joined: 21 Aug 2004 Posts: 95 Location: Birmingham, Alabama
|
Posted: Fri Nov 25, 2005 7:48 am Post subject: |
|
|
An excellent of a heavy car without brake cooling ducts. Chuck _________________ SCCA #36 E30, ITA
BMWCCA #36 E30, MP |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
idanity
![](images/avatars/2079408846526ce0488af0f.jpg)
Joined: 21 May 2005 Posts: 3097 Location: N.W.U.S.A.
|
Posted: Mon May 29, 2006 10:40 am Post subject: |
|
|
just as a joke, try taking them into auto-zone for them to turn the rotors...
and tell them, "i want to see the drilled spots again".. ![Twisted Evil](images/smiles/icon_twisted.gif) _________________
........ .. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Keith M
Joined: 23 Dec 2004 Posts: 216 Location: West Linn, OR
|
Posted: Mon May 29, 2006 12:19 pm Post subject: |
|
|
Anyone had a brake pad crumble? Hawk HT-10's with 4 days on them (one in the wet). I seen small cracks and a few chips before but nothing like this. (A quarter size piece missing from the right front)
Keith _________________ 85 318
96 328is
87 325i |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Tom Olsson Site Admin
Joined: 03 Nov 2004 Posts: 242 Location: Seattle, WA, US
|
Posted: Mon May 29, 2006 3:02 pm Post subject: |
|
|
I actually did see that last weekend. We pulled a set of Pagid oranges off of Bills car that had 2 race weekends and an Enduro on them. The were falling apart with chunks flaking off with about 1/2 the pad left. I think they did see some rain, so I wonder if that's the common denominator, although I've not seen that before. Better safe than sorry, so we tossed 'em. _________________ 07 335i, 91 318is, 87 325is race car #55 Pro-3 |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
idanity
![](images/avatars/2079408846526ce0488af0f.jpg)
Joined: 21 May 2005 Posts: 3097 Location: N.W.U.S.A.
|
Posted: Tue May 30, 2006 6:32 am Post subject: |
|
|
good reply..
i was contemplating on trying the "hawk" pads, not knowing anyone with them, the "reviews" are useally biased..
now i know..to stick with pagid or pbr metal masters ![Idea](images/smiles/icon_idea.gif) _________________
........ .. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Tom Olsson Site Admin
Joined: 03 Nov 2004 Posts: 242 Location: Seattle, WA, US
|
Posted: Tue May 30, 2006 8:49 am Post subject: |
|
|
I've actually heard great things about Hawk HT-10's, and know several people that swear by them. I wouldn't write them off because of Keith's experience. The track puts huge stress on the brakes, and they become almost disposable. I've always got a spare set front and back in my kit all the time.
If you're shopping for E30 track pads, I've also heard very good things about Carbotechs and Porterfield R4's. It all really depends on your braking style, how much intial bite you want, and how good you are at modulating. I just went to a much more agressive pad from the R4 and honestly had problems. A couple of minor lock-ups, and then a major one in the heat of battle that resulted in a flat-spot on a brand new RA1. ![Confused](images/smiles/icon_confused.gif) _________________ 07 335i, 91 318is, 87 325is race car #55 Pro-3 |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Keith M
Joined: 23 Dec 2004 Posts: 216 Location: West Linn, OR
|
Posted: Fri Jun 02, 2006 9:52 am Post subject: |
|
|
Idanity,
For street driving I would not use Hawk HT-10's or other race pads. HPS or HP+ would be a better choice. Be aware that the more aggressive the pad the more dust they produce, plus the cost ($194 for the fronts)
This is the first time we have had any problems with Hawk. We did contact them and are sending the pads back to them for review. I'll bet that there is a new set of pads delivered to us next week.
FWIW The car is a 2900 lb e36 328. Stock rotors, cooling ducts and race pads. As Tom said, at the track you use your brakes HARD. Probably more in 20 min than a week or a month on the street. Try to make to the next track day and get a ride with an instructor, or if your really lucky, one of the PRO3 cars. Those things will pop your eyeballs out under braking.
Keith _________________ 85 318
96 328is
87 325i |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Steve D
Joined: 09 Aug 2004 Posts: 102 Location: San Diego
|
Posted: Sat Jun 03, 2006 6:58 pm Post subject: |
|
|
I use Carbotech XP10's on the front & 9's on the rear. I'd only recommend these with R-comp tires, though. Otherwise I'd suggest 9's in the front & 8's in the rear.
I think I could beat those photos, if I knew how to post a picture on the web. During a 3 hour enduro the cooling duct to the right front rotor severed, which caused the brake to overheat, which caused accelerated wear of the pads. At 2:48 into the race (12 minutes to go!) my pedal went to the floor coming into a corner. I pulled the e-brake and was able to slow down enough to make the corner, but had to pull into the pits with less than 10 min left in the race . When I pulled onto the hot pits, the rotor was billowing smoke - a couple guys ran over with fire extinguishers thinking the car was on fire. Anyway, the next day when I pulled the wheel & looked at the brakes, I found that what had happened was the pad / rotor wore so thin (the pad was down to the backing plate) that the piston pulled the rubber seal out of the caliper, letting the fluid drain out and causing the brake failure. Also, things got so hot that the backing plate literally melted around the piston, and the two pieces welded themselves together. I have no idea what temps are required to weld two solid pieces of metal together, but I apparently hit it whatever it is! _________________ 1989 325is spec e30 / KP race car #31
2000 M5
2001 Dodge Ram - the tow vehicle |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
idanity
![](images/avatars/2079408846526ce0488af0f.jpg)
Joined: 21 May 2005 Posts: 3097 Location: N.W.U.S.A.
|
Posted: Sat Jun 10, 2006 11:37 am Post subject: |
|
|
Steve D wrote: | I
I think I could beat those photos, if I knew how to post a picture on the web. I have no idea what temps are required to weld two solid pieces of metal together, but I apparently hit it whatever it is! |
- to post photos go to a free web space, (few are good, *here* 's my favorite)>
- i dont know the temps on brakes either, but i think its more than standard metals,...and i know you not only found the temperature, but exceeded it so greatly that it mightve been a wonderful show at nighttime...(well, not for you, but for the by-standers)... _________________
........ ..
Last edited by idanity on Sun Jun 18, 2006 3:57 am; edited 1 time in total |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Steve D
Joined: 09 Aug 2004 Posts: 102 Location: San Diego
|
Posted: Sat Jun 10, 2006 5:49 pm Post subject: |
|
|
idanity wrote: | Steve D wrote: | I
I think I could beat those photos, if I knew how to post a picture on the web. I have no idea what temps are required to weld two solid pieces of metal together, but I apparently hit it whatever it is! |
- to post photos go to a free web space, (few are good, *here* 's my favorite)>
- i dont know the temps on brakes either, but i think its more than standard metals,...and i know you not only found the temperature, but exceeded it so greatly that it mightve been a wonderful show at nighttime...(well, not for you, but for the by-standers)... |
Where's you favorite? Oh, nevermind - I didn't catch the link under *here*. _________________ 1989 325is spec e30 / KP race car #31
2000 M5
2001 Dodge Ram - the tow vehicle |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Steve D
Joined: 09 Aug 2004 Posts: 102 Location: San Diego
|
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Chuck Baader
Joined: 21 Aug 2004 Posts: 95 Location: Birmingham, Alabama
|
Posted: Wed Jun 28, 2006 6:49 am Post subject: |
|
|
Steve, I assume you are running a 3" brake duct from someone like Bimmerworld? If that is the case, you certaily have the wrong pads. Try Mintex 1166 compound all round....have used them for years without issues. I do, however, use a brake ballance valve to modulate front to rear ballance. The Porterfield 1110s work well also. Good luck, Chuck _________________ SCCA #36 E30, ITA
BMWCCA #36 E30, MP |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Steve D
Joined: 09 Aug 2004 Posts: 102 Location: San Diego
|
Posted: Wed Jun 28, 2006 12:30 pm Post subject: |
|
|
Chuck - I think the real cause of the problem was starting a 3 hour enduro with 3/4 of pad life remaining, rather than a new set. There was bad accident at the track that afternoon (fatality) which pushed everything back and left me with 1/2 hr to scramble to get everything set up for the enduro and not enough time to change pads. This was then compounded by the severed passenger-side brake duct, which I'm sure accellerated wear (the driver-side pads were very low by the end of the race, but not gone, whereas the passenger-side pads were eating into the backing plate).
I've been using Carbotech 10's for over a year, and this was the first brake-related problem I've had. I've heard good things about the Porterfields as well as Hawks, but haven't tried them. _________________ 1989 325is spec e30 / KP race car #31
2000 M5
2001 Dodge Ram - the tow vehicle |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|